CCNA 200-125

Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three)

Which statements accurately describe CDP? (Choose three)

What are three components that comprise the SNMP framework? (Choose three.)

Which two statements about northbound and southbound APIs are true? (Choose two.)

Which condition indicates that service password-encryption is enabled?

Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Select two)

What can be done to secure the virtual terminal interfaces on a router? (Select two)

View the exhibit. The technician wants to upload a new IOS in the router while keeping the existing IOS. What is the maximum size of an IOS file that could be loaded if the original IOS is also kept in flash?

Which two pieces of information are provided by the show controllers serial 0 command? (Choose two.)

Which two locations can be configured as a source for the IOS image in the boot system command? (Select two)

View the exhibit. The two routers have had their startup configurations cleared and have been restarted. At a minimum, what must the administrator do to enable CDP to exchange information between R1 and R2?

Which two passwords must be supplied in order to connect by Telnet to a properly secured Cisco switch and make changes to the device configuration? (Select two)

What is the purpose of the POST operation on a router?

What are the Popular destinations for syslog messages to be saved? (Choose three)

Which three statements about Syslog utilization are true? (Choose three)

View the exhibit. If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?

Which command is necessary to permit SSH or Telnet access to a Cisco switch that is otherwise configured for these vty line protocols?

View the exhibit. A network administrator configures a new router and enters the copy startup-config running-config command on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?

Which command sets and automatically encrypts the privileged enable mode password?

Which component of the Cisco SDN solution serves as the centralized management system?

Which three features are added in SNMPv3 over SNMPv2?

Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?

An administrator cannot connect from R1 to R2. To troubleshoot this problem, the administrator has entered the command shown in the exhibit. Based on the output shown, what could be the problem?

What is the alert message generated by SNMP agents called?

View the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? (Select two)

Which three commands can you use to set a router boot image? (Choose three.)

View the exhibit. Why is flash memory erased prior to upgrading the IOS image from the TFTP server?

Which fields are contained in a layer 2 Ethernet frame? (Choose three.)

Refer to the exhibit. You have discovered that computers on the 192.168.10.0/24 network can ping their default gateway, but they cannot connect to any resources on a remote network. Which reason for the problem is most likely true?

Which technique can you use to route IPv6 traffic over an IPv4 infrastructure?

On a live network, which commands will verify the operational status of router interfaces? (Choose two)

Which statement about routing protocols is true?

On which OSI layer does a VLAN operate?

Which IPv6 feature is supported in IPv4 but is not commonly used?

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?

Which NTP concept indicates the distance between a device and the reliable time source?

Which NAT command can be applied to an interface?

What is true about Cisco Discovery Protocol?

View the exhibit. What is the most appropriate summarization for these routes?

What are three parts of an IPv6 global unicast address? (Choose three.)