CCNA 200-125

What two things does a router do when it forwards a packet? (Choose two)

View the exhibit. Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?

What are the two default metrics used by EIGRP for route selection? (Choose two.)

Which statements describe the routing protocol OSPF? (Select three)

Why do large OSPF networks use a hierarchical design? (Choose three)

Which statement about slow inter-VLAN forwarding is true?

A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?

Which option describes a difference between EIGRP for IPv4 and IPv6?

What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0?

Which command is used to display the collection of OSPF link states?

Which command enables IPv6 forwarding on a Cisco router?

What information can be used by a router running a linkstate protocol to build and maintain its topological database? (Choose two.)

Which three elements must be used when you configure a router interface for vlan trunking? (Choose three)

Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?

Which dynamic routing protocol uses only the hop count to determine the best path to a destination?

RT1 is unable to establish an OSPF neighbor relationship with RT3. What are possible reasons for this problem? (Choose Two)

Which type of device can be replaced by the use of subinterfaces for VLAN routing?

What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two)

View the exhibit. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Select two)

View the exhibit, Host A pings interface S0/0 on Router3. What is the TTL value for that ping?

What are two drawbacks of implementing a link-state routing protocol? (Select two)

The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router. Which routers are likely to have been elected as DR? (Select two)

Which three statements about link-state routing are true? (Choose three.)

Which command can you enter to set the default route for all traffic to an interface?

Refer to the exhibit. Router Edge-1 is unable to establish OSPF neighbor adjacency with router ISP-1. Which two configuration changes can you make on Edge-1 to allow the two routers to establish adjacency? (Choose two.)

A network administrator is configuring the routers in the graphic for OSPF. The OSPF process has been started and the networks have been configured for Area 0 as shown in the exhibit. The network administrator has several options for configuring router RT2 to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0/24 LAN segment. What configuration tasks could be used to establish this preference? (Choose three)

Which two of these functions do routers perform on packets? (Select two)

Which value is indicated by the next hop in a routing table?

You enter the show ipv6 route command on an OSPF device and the device displays a route. Which conclusion can you draw about the environment?

The network shown in exhibit uses EIGRP as the routing protocol. What path will packets take from a host on the 192.168.10.192/26 network to a host on the LAN attached to router RT1?

Which configuration can you apply to enable encapsulation on a subinterface?

What two things will a router do when running a distance vector routing protocol? (Select two)

View the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?

Which component of a routing table entry represents the subnet mask?

Which three statements about static routing are true? (Choose three.)

What are two benefits of using a single OSPF area network design? (Choose two.)

View the exhibit. Which address and mask combination represents a summary of the routes learned by EIGRP?

Which command can you enter to verify that a BGP connection to a remote device is established?

Assuming that all OSPF routers in a particular area are configured with identical priority values, which of the following values would a router use for OSPF router ID when it does not have a loopback interface?

Which two statements about the OSPF Router ID are true? (Choose two.)