CCNA 2 FINAL 2012 V3

Which multicast address does EIGRP use to send hello and updates packets?

What is the key responsibility of the switching function within a router?

Refer to the exhibit. If the attached device is configured correctly, what action can be taken to change the state of FastEthernet0/0 to Up Up?

Which two commands can be used to modify the default OSPF metric calculation of a link? (Choose two.)

Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)

Refer to the exhibit. Two connected routers are unable to establish adjacency. Based on the show ip ospf interface output, what could be the problem?

What is a characteristic of classful routing?

Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.10.10 and 192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that the ip classless command has been applied on all routers in the network, what other action should the administrator take to ensure that data packets to these addresses are forwarded via the static route?

A router in an EIGRP enterprise network has a default route configured via the interface that connects to the ISP. Which command would the network administrator apply on this router so that other routers in the EIGRP AS 100 network will use this default route?

A network administrator configures a new router and saves the configuration. The router is taken to the installation site and installed. On startup, what component will the router search first by default for the saved configuration?

Refer to the exhibit. A network engineer removes a new router from the shipping container and powers on the router to ensure it passes POST. Which port would the engineer use to perform the initial configuration?

Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hosts on the Internet fail. What is the reason for this problem?

You have been asked to explain converged networks to a trainee. How would you accurately describe a converged network?

A network administrator is troubleshooting a RIPv2 network that is not converging as expected. Which command can the administrator use on each router to view the RIPv2 updates as they are received?

A network administrator is setting up a new router with a device name of Admin, an encrypted password of cangetin, and the IP address 192.168.1.22/29 assigned to the first FastEthernet interface. Which command sequence correctly configures this router?

What is the purpose of the TTL field within an IP packet header?

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

What is the function of the OSPF LSU packet?

Two routers need to be configured within a single OSPF area. Which two components need to be configured on both routers to achieve this? (Choose two.)

Which routing protocol maintains a topology table separate from the routing table?

A router has learned two equal cost paths to a remote network via the EIGRP and RIP protocols. Both protocols are using their default configurations. Which path to the remote network will be installed in the routing table?

Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?

Which two locations can be the source of the Cisco IOS that is used by a router during the bootup process? (Choose two.)

Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. Which set of commands is required to configure a single area OSPF for the networks that are connected to R2?

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.
Which path will be used to transmit the data?