CCNA 2 FINAL 2012 V3

Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?

What is the purpose of the TTL field within an IP packet header?

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

What is the function of the OSPF LSU packet?

Two routers need to be configured within a single OSPF area. Which two components need to be configured on both routers to achieve this? (Choose two.)

Which routing protocol maintains a topology table separate from the routing table?

A router has learned two equal cost paths to a remote network via the EIGRP and RIP protocols. Both protocols are using their default configurations. Which path to the remote network will be installed in the routing table?

Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?

Which two locations can be the source of the Cisco IOS that is used by a router during the bootup process? (Choose two.)

Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. Which set of commands is required to configure a single area OSPF for the networks that are connected to R2?

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.
Which path will be used to transmit the data?

In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?

Which two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)

Refer to the exhibit. A network administrator wants to reduce the size of the routing table of R1. Which partial routing table entry in R1 represents the route summary for R2, without including any additional subnets?

Refer to the exhibit. How many routes are ultimate routes?

Which statement correctly describes a feature of RIP?

Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Router2 in order to put the interface in the same network as the serial interface of Router1?

The command ip route 192.168.2.0 255.255.255.0 172.16.2.2 was entered into the router. After network changes were made, the new next hop for the 192.168.2.0/24 network is 172.16.5.1. What should an administrator do so that the router will use the new next hop to reach the 192.168.2.0 network?

A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?

A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2000 hosts for local LANs. Which subnet mask should the administrator use to create the new subnets?

When connecting two devices, which situation would normally require the use of a crossover cable?

Which router mode is accessed by entering the enable command?

Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?

Refer to the exhibit. Which option will provide the configuration that is needed for router R1 to dynamically learn routes to the 192.168.100.16/28, 192.168.100.32/28, and 192.168.100.48/28 subnetworks?

Refer to the exhibit. The network is configured for RIPv2 routing. What path will a packet from router A take to reach the LAN that is attached to router F if the 56 kb/s link between router A and router E fails?

Refer to the exhibit. Routers R1 and R2 are directly connected through a FastEthernet link but cannot form a neighbor adjacency. What could resolve the problem?

Which feature of RIPv2 enables it to function as a classless routing protocol?

Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?

Refer to the exhibit. A network administrator configures a static route on router R1 to reach the 192.168.1.0/24 network. Which IP address should be used as the next-hop address in the ip route command?

Refer to the exhibit. Which two interface variables will determine the metric that is used on EIGRP routes? (Choose two.)

Which protocol is used by EIGRP to deliver and receive update packets?

Which multicast address does EIGRP use to send hello and updates packets?

What is the key responsibility of the switching function within a router?

Refer to the exhibit. If the attached device is configured correctly, what action can be taken to change the state of FastEthernet0/0 to Up Up?

Which two commands can be used to modify the default OSPF metric calculation of a link? (Choose two.)

Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)