CCNA 2 FINAL 2012 V1

Which of the following are required when adding a network to the OSPF routing process configuration? (Choose 3)

Which of the following are primary functions of a router? (Choose two.)

Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)

Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?

What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks?

Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?

Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?

Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)

A router boots and enters setup mode. What is the reason for this?

Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?

All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID?

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. 
What action should be taken to solve this problem?

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.Which path will be used to transmit the data?

Refer to the exhibit. What is the meaning of the highlighted value 120?

In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?

Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem?

How does route poisoning prevent routing loops?

Which statement is true about the metrics used by routing protocols?
 

Which statement correctly describes a feature of RIP?

Refer to the exhibit. OSPF is used for the routing protocol and all interfaces are configured with the correct IP addresses and subnet masks. During testing, it is found that router R1 is unable to form an adjacency with R2. What is the cause of this problem?

 A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?

Which network and mask combination requires the use of a classless addressing solution?

A company is using static routes that are configured with an administrative distance of “1” on all routers in the network. The network administrator decides to introduce a dynamic routing protocol to reduce the manual configurations for the static routes. Which option identifies the correct procedure for the dynamic routing to take place in the network?

Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?

Refer to the exhibit. When a static IP address is being configured on the host, what address should be used for the default gateway?

Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of addresses and prefixes could be used to create an addressing solution with a minimum waste of IP addresses?

Refer to the exhibit. The network is configured for OSPF routing with default settings. The bandwidths have been configured correctly for each link. If the T1 link between router A and router E fails, what path will a packet from router A take to reach the LAN attached to router F when the network has converged?

Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?

Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?

Which multicast address does EIGRP use to send hello and updates packets?

Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down?

Refer to the exhibit. How was the OSPF default gateway entry for R2 determined?

Refer to the exhibit. RIPv1 has been properly configured on all routers in the network. However, users on LAN2 have intermittent connectivity with the users on LAN1 and LAN3. What is the cause of the problem?

Which default EIGRP configuration must be modified to allow an EIGRP router to advertise subnets that are configured with VLSM?

What is a successor for a destination network in an EIGRP network?