CCNA 2 FINAL 2012 V2

Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols. Which path will be used to transmit the data packets from PC1 to PC2?

Refer to the exhibit. The network administrator has run the following command on R1. R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2 What is the result of running this command?

Why is fast convergence desirable in networks that use dynamic routing protocols?

Which two statements about routing protocols are accurate? (Choose two.)

Refer to the exhibit. If the EIGRP routing protocol is used throughout the network, which IP address and mask prefix
should be sent by router R1 to the Edge router as a result of manual summarization of LANs A, B, C, and D?

Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?

Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?

Which protocol is used by EIGRP to deliver and receive update packets?

Which multicast address does EIGRP use to send hello and updates packets?

A network administrator is using an application that is monitoring packets on the network and sees an EIGRP update packet. What is the purpose of the update packet?

Refer to the exhibit. What OSPF network statements are required for the router B to advertise the three networks that are attached?

Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down?

On a router, which three components are stored in RAM? (Choose three.)

Refer to the exhibit. RouterA and RouterB cannot successfully exchange EIGRP routes. What is the problem?

Refer to the exhibit. What is the purpose of the ip bandwidth-percent eigrp 50 10 command?

A network administrator adds the default-information originate command to the configuration of a router that uses RIP as the routing protocol. What will result from adding this command?

A network technician is configuring a Cisco 2811 router. The technician types conf at the privileged level command prompt and presses the TAB key. What action will the router take?

What is a function of the console port on a router?

Refer to the exhibit. Which route will be installed in the routing table on R1 to forward traffic from PC1 to the web server?

Refer to the exhibit. After the commands are entered, which password will be required to establish a Telnet session
with the router?

Which of the following are primary functions of a router? (Choose two.)
 

Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?

Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through
a router? (Choose three.)

Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?

What is the purpose of the TTL field within an IP packet header?

Refer to the exhibit. How many routes are both level 1 and qualify for use as an ultimate route?

Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?

Refer to the exhibit. Routers 1 and 2 are directly connected over a serial link. Pings are failing between the two routers. What change by the administrator will correct the problem?

Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?

Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?

A router boots and enters setup mode. What is the reason for this?

Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. Which set of commands is required to configure a single area OSPF for the networks that are connected to R2?

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?

Which statement is true about the metrics used by routing protocols?

Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping
192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1.
What is the reason for the ping failure?

Which two statements are true about the EIGRP successor route?

Refer to the exhibit. Hosts on the 192.168.1.0 network cannot communicate with hosts on the 172.16.1.1 network. The network administrator has run the show ip route command on R1. What could be the cause of this problem?