CCNA 2 FINAL 2012 V1

Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of addresses and prefixes could be used to create an addressing solution with a minimum waste of IP addresses?

Refer to the exhibit. The network is configured for OSPF routing with default settings. The bandwidths have been configured correctly for each link. If the T1 link between router A and router E fails, what path will a packet from router A take to reach the LAN attached to router F when the network has converged?

Which candidate route has the longest match for a packet with a destination address of 10.30.16.48?

Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?

Which multicast address does EIGRP use to send hello and updates packets?

Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down?

Refer to the exhibit. How was the OSPF default gateway entry for R2 determined?

Refer to the exhibit. RIPv1 has been properly configured on all routers in the network. However, users on LAN2 have intermittent connectivity with the users on LAN1 and LAN3. What is the cause of the problem?

Which default EIGRP configuration must be modified to allow an EIGRP router to advertise subnets that are configured with VLSM?

What is a successor for a destination network in an EIGRP network?

Refer to the exhibit. Which route will be removed from the routing table if manual EIGRP summarization is disabled on the Serial0/0/0 interface of Router3?

Which port can be used for initial router configuration?

Which two link-state routing protocol challenges does OSPF resolve through the election of a DR? (Choose two.)

A routing table shows an EIGRP route to 192.168.1.0/24 with a metric of 301440. What other term also describes this EIGRP metric value?

Refer to the exhibit. The network administrator has run the following command on R1.
R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2
What is the result of running this command?

Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?

Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once the administrator is connected to the router, which password should the administrator enter at the R1> prompt to access the privileged EXEC mode?

Refer to the exhibit. Which option will provide the configuration that is needed for router R1 to dynamically learn routes to the 192.168.100.16/28, 192.168.100.32/28, and 192.168.100.48/28 subnetworks?

Refer to the exhibit. What will happen when the router reloads?

On a router, which actions can be performed in user mode?

Which of the following are primary functions of a router? (Choose two.)

Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)

Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?

What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks?

Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?

Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?

Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)

A router boots and enters setup mode. What is the reason for this?

Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?

All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID?

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. 
What action should be taken to solve this problem?

Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.Which path will be used to transmit the data?

Refer to the exhibit. What is the meaning of the highlighted value 120?

In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?