card2brain.ch

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)
Case 1:

installing a static route

entering “no switchport” on the port connected to the router

modifying the default VLAN

assigning ports to VLANs

enabling IP routing

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)

Case 2:

assigning ports to VLANs

implementing a routing protocol

creating SVI interfaces

installing a static route

creating VLANs

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)

Case 3:

assigning ports to VLANs

modifying the default VLAN

enabling IP routing

installing a static route

entering “no switchport” on the port connected to the router

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)

Case 4:

installing a static route

enabling IP routing

modifying the default VLAN

assigning ports to VLANs

creating SVI interfaces

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)

Case 5:

assigning ports to VLANs

enabling IP routing

installing a static route

implementing a routing protocol

creating SVI interfaces

A new Layer 3 switch is connected to a router and is being configured for interVLAN routing. What are three of the five steps required for the configuration? (Choose three.)

Case 6:

establishing adjacencies

enabling IP routing

adjusting the route metric

entering “no switchport” on the port connected to the router

assigning ports to VLANs

Which three statements accurately describe duplex and speed settings on Cisco 2960 switches? (Choose three.)

An autonegotiation failure can result in connectivity issues.

When the speed is set to 1000 Mb/s, the switch ports will operate in full-duplex mode.

The duplex and speed settings of each switch port can be manually configured.

Enabling autonegotiation on a hub will prevent mismatched port speeds when connecting the hub to the switch.

By default, the speed is set to 100 Mb/s and the duplex mode is set to autonegotiation.

Refer to the exhibit. A network administrator configures R1 for inter-VLAN routing between VLAN 10 and VLAN 20. However, the devices in VLAN 10 and VLAN 20 cannot communicate. Based on the configuration in the exhibit, what is a possible cause for the problem?

https://itexamanswers.net/wp-content/uploads/2020/01/2021-12-19_221231.jpg?ezimgfmt=ng:webp/ngcb2

A. The port Gi0/0 should be configured as trunk port.

B. The encapsulation is misconfigured on a subinterface.

C. A no shutdown command should be added in each subinterface configuration.

D. The command interface gigabitEthernet 0/0.1 is wrong.

A network administrator uses the spanning-tree portfast bpduguard default global configuration command to enable BPDU guard on a switch. However, BPDU guard is not activated on all access ports. What is the cause of the issue?

BPDU guard needs to be activated in the interface configuration command mode.

Access ports configured with root guard cannot be configured with BPDU guard.

Access ports belong to different VLANs.

PortFast is not configured on all access ports.

Which two types of spanning tree protocols can cause suboptimal traffic flows because they assume only one spanning-tree instance for the entire bridged network? (Choose two.)

MSTP

RSTP

Rapid PVST+

PVST+

STP

Refer to the exhibit. A network administrator is configuring the router R1 for IPv6 address assignment. Based on the partial configuration, which IPv6 global unicast address assignment scheme does the administrator intend to implement?

https://itexamanswers.net/wp-content/uploads/2020/01/i282171v1n1_282171.png?ezimgfmt=ng:webp/ngcb2

stateful

stateless

manual configuration

SLAAC

A WLAN engineer deploys a WLC and five wireless APs using the CAPWAP protocol with the DTLS feature to secure the control plane of the network devices. While testing the wireless network, the WLAN engineer notices that data traffic is being exchanged between the WLC and the APs in plain-text and is not being encrypted. What is the most likely reason for this?

DTLS only provides data security through authentication and does not provide encryption for data moving between a wireless LAN controller (WLC) and an access point (AP).

Although DTLS is enabled by default to secure the CAPWAP control channel, it is disabled by default for the data channel.

DTLS is a protocol that only provides security between the access point (AP) and the wireless client.

Data encryption requires a DTLS license to be installed on each access point (AP) prior to being enabled on the wireless LAN controller (WLC).

A new switch is to be added to an existing network in a remote office. The network administrator does not want the technicians in the remote office to be able to add new VLANs to the switch, but the switch should receive VLAN updates from the VTP domain. Which two steps must be performed to configure VTP on the new switch to meet these conditions? (Choose two.)

Configure the new switch as a VTP client.

Configure the existing VTP domain name on the new switch.

Configure an IP address on the new switch.

Configure all ports of both switches to access mode.

Enable VTP pruning.

Refer to the exhibit. Consider that the main power has just been restored. PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?

https://itexamanswers.net/wp-content/uploads/2020/01/i245718v1n1_1.png?ezimgfmt=ng:webp/ngcb2

to Fa0/1, Fa0/2, and Fa0/3 only

to Fa0/1, Fa0/2, Fa0/3, and Fa0/4

to Fa0/1 only

to Fa0/1, Fa0/2, and Fa0/4 only

to Fa0/1 and Fa0/2 only

What action takes place when the source MAC address of a frame entering a switch is not in the MAC address table?

The switch adds a MAC address table entry for the destination MAC address and the egress port.

The switch adds the MAC address and incoming port number to the table.

The switch replaces the old entry and uses the more current port.

The switch updates the refresh timer for the entry.

Employees are unable to connect to servers on one of the internal networks. What should be done or checked?

Use the “show ip interface brief” command to see if an interface is down.

Verify that there is not a default route in any of the edge router routing tables.

Create static routes to all internal networks and a default route to the internet.

Check the statistics on the default route for oversaturation.

What is the effect of entering the ip dhcp snooping configuration command on a switch?

It enables DHCP snooping globally on a switch.

It enables PortFast globally on a switch.

It disables DTP negotiations on trunking ports.

It manually enables a trunk link.

An administrator notices that large numbers of packets are being dropped on one of the branch routers. What should be done or checked?

Create static routes to all internal networks and a default route to the internet.

Create extra static routes to the same location with an AD of 1.

Check the statistics on the default route for oversaturation.

Check the routing table for a missing static route.

What are two switch characteristics that could help alleviate network congestion? (Choose two.)

fast internal switching

large frame buffers

store-and-forward switching

low port density

frame check sequence (FCS) check

What is a result of connecting two or more switches together?

The number of broadcast domains is increased.

The size of the broadcast domain is increased.

The number of collision domains is reduced.

The size of the collision domain is increased.

Branch users were able to access a site in the morning but have had no connectivity with the site since lunch time. What should be done or checked?

Verify that the static route to the server is present in the routing table.

Use the “show ip interface brief” command to see if an interface is down.

Check the configuration on the floating static route and adjust the AD.

Create a floating static route to that network.

What is the effect of entering the switchport port-security configuration command on a switch?

It dynamically learns the L2 address and copies it to the running configuration.

It enables port security on an interface.

It enables port security globally on the switch.

It restricts the number of discovery messages, per second, to be received on the interface.

A network administrator is configuring a WLAN. Why would the administrator use multiple lightweight APs?

to centralize management of multiple WLANs

to monitor the operation of the wireless network

to provide prioritized service for time-sensitive applications

to facilitate group configuration and management of multiple WLANs through a WLC

Refer to the exhibit. PC-A and PC-B are both in VLAN 60. PC-A is unable to communicate with PC-B. What is the problem?
https://itexamanswers.net/wp-content/uploads/2016/02/i211586v1n1_Question-5.png?ezimgfmt=ng:webp/ngcb2

The native VLAN should be VLAN 60.

The native VLAN is being pruned from the link.

The trunk has been configured with the switchport nonegotiate command.

The VLAN that is used by PC-A is not in the list of allowed VLANs on the trunk.

A network administrator is configuring a WLAN. Why would the administrator use RADIUS servers on the network?

to centralize management of multiple WLANs

to restrict access to the WLAN by authorized, authenticated users only

to facilitate group configuration and management of multiple WLANs through a WLC

to monitor the operation of the wireless network

What is the effect of entering the switchport mode access configuration command on a switch?

It enables BPDU guard on a specific port.

It manually enables a trunk link.

It disables an unused port.

It disables DTP on a non-trunking interface.

A network administrator has configured a router for stateless DHCPv6 operation. However, users report that workstations are not receiving DNS server information. Which two router configuration lines should be verified to ensure that stateless DHCPv6 service is properly configured? (Choose two.)

The domain-name line is included in the ipv6 dhcp pool section.

The dns-server line is included in the ipv6 dhcp pool section.

The ipv6 nd other-config-flag is entered for the interface that faces the LAN segment.

The address prefix line is included in the ipv6 dhcp pool section.

The ipv6 nd managed-config-flag is entered for the interface that faces the LAN segment.

A network administrator is configuring a WLAN. Why would the administrator disable the broadcast feature for the SSID?

to eliminate outsiders scanning for available SSIDs in the area

to centralize management of multiple WLANs

to facilitate group configuration and management of multiple WLANs through a WLC

to provide prioritized service for time-sensitive applications

Refer to the exhibit. An administrator is attempting to install an IPv6 static route on router R1 to reach the network attached to router R2. After the static route command is entered, connectivity to the network is still failing. What error has been made in the static route configuration?

https://itexamanswers.net/wp-content/uploads/2019/12/2020-01-17_100010.jpg?ezimgfmt=rs:734x316/rscb2/ng:webp/ngcb2

The next hop address is incorrect.

The interface is incorrect.

The destination network is incorrect.

The network prefix is incorrect.

What action takes place when a frame entering a switch has a unicast destination MAC address that is not in the MAC address table?

The switch updates the refresh timer for the entry.

The switch resets the refresh timer on all MAC address table entries.

The switch replaces the old entry and uses the more current port.

The switch will forward the frame out all ports except the incoming port.

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Create a floating static route to that network.

Check the configuration on the floating static route and adjust the AD.

Check the configuration of the exit interface on the new static route.

Verify that the static route to the server is present in the routing table.

What is the effect of entering the ip arp inspection vlan 10 configuration command on a switch?

It specifies the maximum number of L2 addresses allowed on a port.

It enables DAI on specific switch interfaces previously configured with DHCP snooping.

It enables DHCP snooping globally on a switch.

It globally enables BPDU guard on all PortFast-enabled ports.

What protocol or technology manages trunk negotiations between switches?

VTP

EtherChannel

DTP

STP

A network administrator is configuring a WLAN. Why would the administrator apply WPA2 with AES to the WLAN?

to reduce the risk of unauthorized APs being added to the network

to centralize management of multiple WLANs

to provide prioritized service for time-sensitive applications

to provide privacy and integrity to wireless traffic by using encryption

Users on a LAN are unable to get to a company web server but are able to get elsewhere. What should be done or checked?

Ensure that the old default route has been removed from the company edge routers.

Verify that the static route to the server is present in the routing table.

Check the configuration on the floating static route and adjust the AD.

Create a floating static route to that network.

What IPv6 prefix is designed for link-local communication?

2001::/3

ff00::/8

fc::/07

fe80::/10

What is the effect of entering the ip dhcp snooping limit rate 6 configuration command on a switch?

It displays the IP-to-MAC address associations for switch interfaces.

It enables port security globally on the switch.

It restricts the number of discovery messages, per second, to be received on the interface.

It dynamically learns the L2 address and copies it to the running configuration.

A network administrator is configuring a WLAN. Why would the administrator change the default DHCP IPv4 addresses on an AP?

to eliminate outsiders scanning for available SSIDs in the area

to reduce the risk of unauthorized APs being added to the network

to reduce outsiders intercepting data or accessing the wireless network by using a well-known address range

to reduce the risk of interference by external devices such as microwave ovens

What is the effect of entering the ip arp inspection validate src-mac configuration command on a switch?

It checks the source L2 address in the Ethernet header against the sender L2 address in the ARP body.

It disables all trunk ports.

It displays the IP-to-MAC address associations for switch interfaces.

It enables portfast on a specific switch interface.

What protocol or technology is a Cisco proprietary protocol that is automatically enabled on 2960 switches?

DTP

STP

VTP

EtherChannel

CISCO CCNA SWRE 2

Flashcards

CISCO CCNA SWRE 2

Create or copy sets of flashcards

Flashcards

Please log in

Google

Apple ID

Microsoft

Switch edu-ID

Edulog

Google

Apple ID

Microsoft

Switch edu-ID

Edulog